#Xmenu xbox360 how to#
#Xmenu xbox360 1080p#
#Xmenu xbox360 install#
#Xmenu xbox360 software#
#Xmenu xbox360 code#

Backup Nand Dumps Files, ECC, CPU Key, UpdFlash.etc Somewhere Safe.PC > J-Runner v0.3 Beta8 (Run As Admin) > Write Nand > Type > OK.Note2: it should generate a new file once finish J-Runner > Load Source > updflash.bin.Delete it? Unless you put it there, delete it! > YES PC > J-Runner v0.3 Beta8 (Run As Admin) > Create XeBuild Image.Set to Read & Write Mode: JR Programmer V2 > Switch To The Left (RED).Connect Xbox 360 Standby Power to the Xbox 360 (DO NOT POWER ON).

#Xmenu xbox360 install#

RGH1.2 PHAT Step 6: Install XeBuild & Write Nand.

Note: Now we have more info: J-Runner > KV Info.

PC > J-Runner v0.3 Beta8 (Run As Admin) > IP > Get CPU Key.

Note: Xell > Network Config > 192.168.1.XXX easy way to get cpu key using this ip.

Bootup the Xbox 360 > Wait for Xell Reloaded to Complete its startup process.

Note: This will write Xell to the Xbox 360.

PC > J-Runner v0.3 Beta8 (Run As Admin) > Write ECC > Type > OK.

Note: J-Runner > Load > Source should now say: image_00000000.ecc.

PC > J-Runner v0.3 Beta8 (Run As Admin) > Create ECC > Type > OK.

Backup The Nand Dumps Files (nanddump1.bin nanddump2.bin checksum.md5) Somewhere Safe.

When It Finish It Should Say: NANDS ARE THE SAME.

Common To See 'Error: 250 Reading Block AA0', Any Where Between 10-15 Error Blocks, Just Make Sure They Are The Same On Both Dumps.

Each Nand Dumps should take about 5-15mins each, so 10-30mins total on the JR Programmer V2.

PC > J-Runner v0.3 Beta8 > Read Nand > Type > OK.

If You Get Flash Config 0x0000000 Then Double Check The Standby Power & Jr Programmer Switch In Correct Place.

This will check which motherboard your console has.

PC > J-Runner v0.3 Beta8 (Run As Admin) > Motherboard > ?.

Connect NAND Header Wire > JR Programmer V2 > USB > PC.

Set to BL Mode: JR Programmer V2 > Switch To The Right (Green).

Xbox 360 > Settings > System > Console Settings > Audio > Sound Effects > Enable Sound Effects.

Xbox 360 > Settings > System > Console Settings > Audio > Digital Output.

#Xmenu xbox360 1080p#

Xbox 360 > Settings > System > Console Settings > Display > HDTV Settings > 1080p.

Xbox 360 > Settings > System > Console Settings > Display > Display Discovery > Disable.

Take apart Slim Model Front Plate (Glossy Trinity):.

Take apart Slim Model (Glossy Trinity):.

#Xmenu xbox360 how to#

Which Mod Chip Install Do I Use? How To Take Apart The Xbox 360? Xbox 360 > Settings > System > Console Settings > System Info.How To Check My Xbox 360 Dashboard Version?

#Xmenu xbox360 code#

The RGH modification is a time based attack on the CPU that glitches the chip, and allows a moment for the exploit to take place and unsigned code to be run.

#Xmenu xbox360 software#

The JTAG modification is a software hack based upon an exploitable SMC which is why it can only be done to Kernals 7371 or lower and was patched in the 8XXXX+ kernals. Both of these modification methods achieve the same thing, just in different ways, and they both have different requirements. I personally have my profile and all my saves on a USB drive, that way I can continue playing no matter what Xbox 360 i am on, I find this very useful when having Xbox 360 lans where i might not always be on my own console.Xbox 360 Modchip Install What is JTAG/RGH?Ī JTAG/RGH exploited console is modified to enable the running unsigned code. That's it, a very simple way to increase the storage capabilities of your 360, or an easy way to have a big memory card you can backup all your save games and content to.

Games should ask you if you wish to save on the USB drive from now on, you can also copy your saves on to it as a backup. You will now be able to access the content stored on the device from within the Xbox 360 dashboard: The USB storage device will be tested, if its fast enough to be used in the Xbox 360 it will be configured:Īll been well your memory stick will be setup fine: You will be warned that everything will be erased from the USB device, so be sure if you have anything on it you want, copy it elsewhere first: The options shown if you select Customise: You will have two options, 'Configure Now' and 'Customise':Ĭonfigure now will use all the space on the USB device for Xbox 360 storage, Customise will let you choose how much space you wish to reserve for use on the Xbox 360: The maximum space you can reserve for 360 use on each device is now 2TB with later dashboard updates.įirst connect your USB memory stick to the consoles USB port, it doesn't matter which one: Note: you can have a maximum of 2x usb memory devices / hard drives configured for Xbox 360 use connected to the console at any one time. So here is a quick tutorial on how to use a USB memory stick up to 16gb, to store save games, profiles, games and dlc. This is very simple to do, however I have had a fair few messages about this lately, and many people dont even know its possible.